Видео

Pushing that chisel towards your hand/arm while you are physically holding the pieces down is sketchy and an accident waiting to happen... I had to hold my breath as you muscled through those lap joint scenes. invest or use a clamp or two and save yourself some losses and future down time. Its just a matter of time till the gotcha moment happens.

Commenting to say your workbench is built exactly like mine. Simple 2x4 frame, 4x4 legs with a plywood slab on top. Gets the job done!

Thank you for your service 🇺🇸

That's awesome but my husband is a chimney inspector and the stove needs to be 18 inches from the wall. Plus there's a 10/2 rule for the chimney. God Bless. Everyone got to be a critical

NO accounting for wood movement! It’ll be full of cracks in just a few years. Sad. 😢😢😢

Thanks! *Approximately* how much time do you think it takes to make each chair?

done deal! great job!

What size eyebolts are in the swing?

I would like to see rubber gloves on his hands.

Awesome, thanks for sharing ❤

Wow U discovered an expensive version of Naval Jelly been around since before U were born!

I like this build. Simple, direct. You might think about only making one side of the fence “square”. The other can actually be rounded and a little loose. The way the fence slides easily. Often times you don’t need the fence to be square to the table because you are using a cutter with a bearing. In that case the critical layout is the height of the cutter only. You won’t even use the fence. Keeping the fence plumb to the table surface will be more critical. Good RUclips! Thank you for sharing your creativity and your knowledge.

18:42 thickened epoxy. Wet the area with the liquid epoxy first.

I got a bit queezy seeing him work with the chissel. I was teaching my son and his friend how to use a wood chissel a few years ago and as I was explaining to alway keep your had behind the business end of the chissel I accidently put mine in from and drove into my index finger. The sacrifices I make just to give my son a clear example.

I can't tell where the saw-dust ends and the glue starts! CRINGE!

Hello D,M I noticed when you were drilling the pocket holes you never drill down to the Drill stop?.Not a Criticism just wondering.Great Console by the way.

Yes get yourself a few bottles for just in case.

Good job mike lol dam kids filming on his phone lol

Tank's verry interesting

Cool video. I didnt know they used glass marbles, but it does make sense that they would. Glass is cheaper than steel and it wont react with whatever is in the can. But i always assumed it was a ball bearing or something. Thanks for posting this im glad i watched

Hi, is it stable ant not rolling back when swinging? I plan to make this for my kid so the swing might be taken for a wild ride

bro... I recognized your voice instantly from your flying channel. Thats so funny. just passed my ppl a couple days ago, your videos were a huge help 😂 Now i need your stain removal training

Good to know that this product works on concrete oil stains. There are so many contractors with oil leaking vehicles and equipment staining my driveway and street.

What are the size/length of the bras nails?

"No specialty tools needed." _[used specialty tools throughout video]_

@DIYMAN. What is the finished dimensions of the chair please

What is the completed dimensions of the chair please

Muratic acid works best

How much weight can it hold?

I got this cutting board for my wife for Valentine's Day two years ago and now I'm single. lol

shit goo of shit i did

Thank you so much for ideas dude

Should the forms be sprayed with release agent before pouring the concrete?

What length of pocket screws did you use?

If you check your joints - they are most probably double the width of your saw blade as I don't think you considered the material loss from the blade width, common mistake.

This video is a hard 'watch'...couldn't finished it. Some very dangerous moments in it too, using cutting tools one-handed! Far too much effort. Just buy a table!

Watched a few kitchen organization videos but didn't see any like this. Decided to search can food organizers. Saw this and it's exactly what I want to build. We have lots of canned foods and sitting them on shelves isn't working. Always end up putting new cans in front of older ones instead of rotating them to use the oldest first.

There is no shoulder formed to stop screw head from passing all the way through

Kreg do not want this video banned. This may be a good idea. I won't know because I'm not going to watch based on your stupid opening premise. People who are interested in this kind of content don't need to be manipulated into watching

Really nice project. Thanks for sharing it. If the table isn't quite as stable as you'd like, you might stiffen the back side and possible even the back side of the sides with a couple of plywood gussets at the top. If I do this, I'd also add a dust collection port on the back of the fence.

Mix caustic soda and wall papir adhecive and just a little water. You wil have same product whitout color. OUTSIDE use only ;)

Oh no not the Bigfoot! I get the rusty tools. Removing the Patina from Bigfoot is a no no. People pay top dollar for that stuff. Lol. Thanks for sharing.

Your time is surely worth more than the cost of the jig. Well done though

VERY NICE video!! I’ll m a beginner woodworker with already a lotta scrap wood layin around, I find this vid should help me out a bunch! Thanks

What size floor joist are they?

I would have worried about clamps before a router table. Glad you still have all your fingers after that chisel work.

a very messy worker when gluing up wood chips need to be removed from work surface

Just curious for the braces that attach to the seat what size screws and setting did you use for the pocket holes ? Just had my 2 1/2 inch screws blow through the back of my 1x2

Most miter saws have a depth stop

I like how simple it is. The router table I'm building has taken me over a month. Still not done. Mine has sliding drawers, doors for bottom etc etc.